Clock-audio CU2 User Manual download pdf

P R O F E S S I O N A L M I C R O P H O N E S Y S T E M S

Intelligent

battery management system designed for use wit

CW 9006T



Processor controlled



Built

In active monitoring system



Temperature sensor



Dedicated compartments for

charging two CW 9004T,

9005T or CW 9006T



Must be used with AC power

adaptor supplied with each CU 2.

User Guide

Insert one or two wireless microphone transmitters in to the charger with the metal charging

points facing

down.

See fig 1

There are two LEDs. The LED closest to the power supply input is for the charging bay on the

right. The LED furthest away from the power supply input is for the charging bay on the left.

The LED will light up red to show that the

The transmitters are charged independently. Each transmitter may take up to 8 hours to charge

depending on the capacity of the batteries and how flat the batteries are.

The LED will light up green

when the transmitter in that charging bay is fully charged.

The fully

charged transmitter can be removed and replaced with another transmitter that

requires charging, even if there is a charging transmitter in the other charging bay.

Fig 1

P R O F E S S I O N A L M I C R O P H O N E S Y S T E M S

battery management system designed for use wit

h Clockaudio CW 9004T, CW 9005T

CW 9006T

wireless base transmitters

In active monitoring system

adaptor supplied with each CU 2.

Insert one or two wireless microphone transmitters in to the charger with the metal charging

There are two LEDs. The LED closest to the power supply input is for the charging bay on the

right. The LED furthest away from the power supply input is for the charging bay on the left.

The LED will light up red to show that the

transmitter in that charging bay is charging.

The transmitters are charged independently. Each transmitter may take up to 8 hours to charge

depending on the capacity of the batteries and how flat the batteries are.

when the transmitter in that charging bay is fully charged.

charged transmitter can be removed and replaced with another transmitter that

requires charging, even if there is a charging transmitter in the other charging bay.

Turn

transmitter off

Place

transmitter in

to charging bay

Red LED

(Checking

battery and

charging)

Green LED

(Charged)

Red LED

flashing (FAULT

battery)

Fig 2

www.clockaudio.com

CU 2

h Clockaudio CW 9004T, CW 9005T

and

Insert one or two wireless microphone transmitters in to the charger with the metal charging

There are two LEDs. The LED closest to the power supply input is for the charging bay on the

right. The LED furthest away from the power supply input is for the charging bay on the left.

transmitter in that charging bay is charging.

See fig 2

The transmitters are charged independently. Each transmitter may take up to 8 hours to charge

when the transmitter in that charging bay is fully charged.

See fig 3

charged transmitter can be removed and replaced with another transmitter that

requires charging, even if there is a charging transmitter in the other charging bay.

Red LED

flashing (FAULT

battery)

CAUTION: Always

turn off the wireless

microphone

transmitter before

putting the

transmitter in to the

charger.

Fig 3

1 2

Summary of Contents

Page 1

P R O F E S S I O N A L M I C R O P H O N E S Y S T E M SAnIntelligentbattery management system designed for use witCW 9006TProcessor controlledBuil

Page 2

FAULTS WITH ONE OF THE TRANSMITTERSBattery FaultRed flashing light will showimmediatelyif alkaline or other non rechargeable batteries havebeen used.

Comments to this Manuals

No comments

Clock-audio CU2 User Manual

Browse online or download User Manual for Microphones Clock-audio CU2. Clock Audio CU2 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Microphones Clock-audio CU2